Artel DLT710 Uživatelský manuál stáhnout pdf

Simplifying Media Transport

™

DigiLink Media Transport Simplied

QUICK START GUIDE

Artel ships the DLT710 congured as follows:

• All signal types enabled (3G, HD, SD, DVB-ASI, ATSC)

• Electrical input set to BNC

• Front panel GEN/CHK switch set to CHK

• LEDS indicate checker status

• Monitor jack contains copy of input BNC

• Multi-format, continuous test mode enabled

• Signal check test interval set to 60 seconds

• Signal check synchronization interval set to 5 seconds

• SDI generator pattern set to color bars, full screen @ 75%

• 1080p 59.94 frames/sec

• 1080i 29.97 frames/sec

• 525i 29.97 frames/sec

• Embedded audio is 1 kHz tone @ -20 dBfs, all 4 channels of audio group 1

• DVB-ASI and ATSC generator transport stream

• SMPTE color bars with moving block

• MPEG-2 single program @ 19.292 Mb/s

• SD video format, 720x480i, 29.97 fps

• Embedded audio is left/right channel, 1 kHz tone @ -20 dBfs, AC-3 format

• Report data rate frequency errors > 40 ppm

• Report inverted DVB-ASI format

• EMS override is allowed (DigiLink Manager can change the DLT710 conguration)

S5 S6 S7 Checker Input

On On On BNC In

O O O Backplane 1

O On O Backplane 2

O O On Backplane 3

O On On Backplane 4

Factory Default: All On

DIP Switch Congurations

Function O On

EMS

Override

Local Remote

Factory Default: All On

SW2 CONFIGURATION

Function O On

HD Vert Res

720p

1080i

Format

625 Line (SD)

50 Field

(HD/3G)

525 Line

(SD)

59.94 Field

(HD/3G)

S3 Reserved - Default

S4 Reserved - Default

Factory Default: All On

SW1 CONFIGURATION

Function O On

S1 Reserved - Default

S2 Reserved - Default

S3 Reserved - Default

S4 Reserved - Default

S5 Reserved - Default

ASI INV Test

Disabled Enabled

S7 Freq Test Disabled Enabled

Sync Interval

Custom Normal

Factory Default: All On

SW1

REAR PANEL SWITCHES

Function O (Down) On (Up)

SDI Pattern

Pathological

Color Bars

3G-SDI

Disabled

Enabled

S3 HD-SDI

Disabled

Enabled

S4 SD-SDI Disabled

Enabled

S5 ASI Disabled Enabled

S6 ATSC Disabled Enabled

Check Mode

Single-Pass

Test

Continuous

Test

Signal

Test Inter-

val

Custom Normal

Factory Default: All On

Monitor Mode: All O (See User Manual for Details)

SW2

SW1 Determines a portion of the test

timing and enables test features

SW2 Determines signal format, input

source, and EMS functionality

Determines test pattern type, signal

type, test mode (continuous or single

pass), and length of test

Conguration Switch Functions

Rear

Panel

Switch

REAR PANEL

SWITCH LOCATION

Multi-Format Digital Video Generator and Test Module

[DLT710]

1 2

Shrnutí obsahu

Strany 1

Simplifying Media Transport™DigiLink Media Transport SimpliedQUICK START GUIDEArtel ships the DLT710 congured as follows: • All signal types enable

Strany 2 - Test Module [DLT710]

www.artel.com | 978-263-5775 | [email protected] | [email protected] Panel LEDsFront LEDFunction Color DescriptionOKDLT710ModuleStatusn GreenN

Komentáře k této Příručce

Žádné komentáře

Artel DLT710 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Artel DLT710. Artel DLT710 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Hardware Artel DLT710